4 thoughts on “How to tie the rope on the ring on the ring”
Julio
Spare materials: ring, red rope, scissors, lighter. 1, first of all, we prepare a red rope and fold the red rope at each other, as shown in the figure. 2, after the red line is folded into a U -shaped, the long end of it is pulled to make it long. 3, then pinch the ring line between the left and right thumbs and the index finger to press the U -shaped line between the ring ring and the index finger, and wrap the long one end of the U -shaped line from left to right to the ring ring. Essence 4, after wound, bypass the excess rope through this circle. 5, and then tighten the other side of the rope. After tightening, cut off the excess red rope on both sides, but do not cut all 1-2 mm, 6, tighten the two sides and then put the two sides on both sides before tightening the two sides. The excess red rope is cut off, but don't cut it all by 1-2 mm. 7, after cutting off, we used the lighter to scal the red rope just left to reinforce. 8, this is complete.
Tie the rope on the ring, the materials that need to be prepared include: ring, red rope, scissors, lighter n. Putting a circle of red rope around a circle . Press the circle with your fingers on the ring, take it, take it, take it, take, The end of the rope three, to the side of the circle, a circle around the ring . After the wind is done, the excess rope is bypassing this circle . tightened the rope The other end of 6. The extra rope is cut with scissors, leaving a little . Burn the two ends of the rope with a lighter , the effect is shown in the figure
Tutoring red rope tutorial on the ring: The professional is "flat knot", which is relatively strong and durable.
The compilation method as shown below:
The method is as follows: 1, first fold a red line into U -shaped, pull it in it At one end, it becomes long and short. 2, then pinch the ring line between the left and right thumbs and the index finger to press the U -shaped line between the ring ring and the index finger. 3. The end of the U -shaped line is circled from left to right to the ring. At the same time, the short ends should be wrapped in. The unblied end of the opening has a buckle, which feels like the scope of the winding is almost the same, and then the opposite direction (that is, from the right to the left). The shorter end. 4. Put the line head through the buckle from the right to the left to the line buckle, and then pull the thread head that pass through the buckle and the shorter line on the right. It is pulled into the wiring line, so there is no need to knot it, and finally cut off the excess line head.
The steps are a bit complicated ... but it should be very simple to do ~~~ First ... fold the red line to the ring that you need to entangle the red thread ... The disconnected ... There is one end connected ... Second ... pick a line from the end of the disconnected end .. A small pimple .... The line of the knot starts to start to the connection The end of a one -end is around ... a circle and one circle ~~ Tree tightened ~~~ That is to say, after you finish the line ~~~~ One end is connected to the line ... There is only one line on one end. ... Third ... After the line is done ... Put the line you around in the connected end .... Then pull the remaining line left on the other end ... you will Discover ... the end of the connected end shrinks ... Finally, pull the line you wound into the circle where you are around .... tightened ... Cut off with scissors Line ... this is ok ...
Spare materials: ring, red rope, scissors, lighter.
1, first of all, we prepare a red rope and fold the red rope at each other, as shown in the figure.
2, after the red line is folded into a U -shaped, the long end of it is pulled to make it long.
3, then pinch the ring line between the left and right thumbs and the index finger to press the U -shaped line between the ring ring and the index finger, and wrap the long one end of the U -shaped line from left to right to the ring ring. Essence
4, after wound, bypass the excess rope through this circle.
5, and then tighten the other side of the rope. After tightening, cut off the excess red rope on both sides, but do not cut all 1-2 mm,
6, tighten the two sides and then put the two sides on both sides before tightening the two sides. The excess red rope is cut off, but don't cut it all by 1-2 mm.
7, after cutting off, we used the lighter to scal the red rope just left to reinforce.
8, this is complete.
Tie the rope on the ring, the materials that need to be prepared include: ring, red rope, scissors, lighter n. Putting a circle of red rope around a circle
. Press the circle with your fingers on the ring, take it, take it, take it, take, The end of the rope
three, to the side of the circle, a circle around the ring
. After the wind is done, the excess rope is bypassing this circle
. tightened the rope The other end of
6. The extra rope is cut with scissors, leaving a little
. Burn the two ends of the rope with a lighter
, the effect is shown in the figure
Tutoring red rope tutorial on the ring:
The professional is "flat knot", which is relatively strong and durable.
The compilation method as shown below:
The method is as follows:
1, first fold a red line into U -shaped, pull it in it At one end, it becomes long and short.
2, then pinch the ring line between the left and right thumbs and the index finger to press the U -shaped line between the ring ring and the index finger.
3. The end of the U -shaped line is circled from left to right to the ring. At the same time, the short ends should be wrapped in. The unblied end of the opening has a buckle, which feels like the scope of the winding is almost the same, and then the opposite direction (that is, from the right to the left). The shorter end.
4. Put the line head through the buckle from the right to the left to the line buckle, and then pull the thread head that pass through the buckle and the shorter line on the right. It is pulled into the wiring line, so there is no need to knot it, and finally cut off the excess line head.
The steps are a bit complicated ... but it should be very simple to do ~~~ First ... fold the red line to the ring that you need to entangle the red thread ... The disconnected ... There is one end connected ... Second ... pick a line from the end of the disconnected end .. A small pimple .... The line of the knot starts to start to the connection The end of a one -end is around ... a circle and one circle ~~ Tree tightened ~~~ That is to say, after you finish the line ~~~~ One end is connected to the line ... There is only one line on one end. ... Third ... After the line is done ... Put the line you around in the connected end .... Then pull the remaining line left on the other end ... you will Discover ... the end of the connected end shrinks ... Finally, pull the line you wound into the circle where you are around .... tightened ... Cut off with scissors Line ... this is ok ...